收藏本站
ISL6144
PCB Layout Considerations
The ISL6144EVAL1Z uses a 4 layer PCB with 1oz external
layers and 2oz internal layers, dedicated ground and power
planes are used to insure good efficiency and EMC
performance. Other layer stack-up and thickness is possible
depending on the particular power system.
The power traces are designed to handle at least 20A of
load per feed. Power and ground planes are made of 2oz
copper and external signal/power layers are 1oz copper.
The loop area for all power traces is minimized to reduce
parasitic inductance.
A ground island can be created under the IC and connected
to the power ground at a single point for reduction of noise
that may be injected from the power ground into the IC
ground.
Component Selection Summary
Component selection is listed for one feed and is applicable
for all other parallel feeds.
R 1 , R 2 - are resistors that define the HS comparator
threshold voltage used in the high speed turn-off. The sum of
R1+ R2 ? 50k Ω. R1 and R2 are found using Equation 17.
R 3 - is a pull-up resistor on the FAULT pin that can be used if
LED1 is not used. FAULT is an open drain that can be used
to interface with an optocoupler, LED or directly to a logic
circuit. This resistor is not populated on the EVAL board.
R 4 - is the FAULT pin LED current limit resistor, R4 is chosen
to have an LED current of about 4mA.
C 1 - is the HVREF Capacitor, placed between VIN and
HVREF pins, this capacitor is necessary to stabilize the
HV REF(VZ) supply and a value of 150nF is sufficient.
Increasing this value will result in gate turn-on time increase.
C 2 - is the COMP Capacitor, Placed between VOUT and
COMP pins to provide filtering and decoupling. A 10nF
capacitor is adequate for most cases.
C 5 , C 6 - are VIN and VOUT local decoupling capacitors,
help immunize the pins against transients that might result in
case of fast speed gate turn-off.
Q 1 -Q 3 - are ORing MOSFET(s), number of paralleled
MOSFETs depends on device r DS(ON) , maximum allowable
losses and junction temperature of the ORing MOSFETs.
U3 - is Intersil’s ISL6144 High Voltage ORing MOSFET
Controller IC.
LED1 - is a red LED used to indicate first feed faults. When
V IN 1 is off while V OUT and auxiliary 5V supply are present
LED1 will be red.
List of Test Points and Connectors
V IN 1 - J4
26
SOURCE1 - TP1, TP17
DRAIN1 - TP2, TP18
GATE1 - TP13
HVREF1 - TP9
COMP1 - TP11
VSET1 - TP10
FAULT1 - TP3
V IN 2 - J7
SOURCE2 - TP4, TP21
DRAIN2 - TP5, TP22
GATE2 - TP14
HVREF2 - TP8
COMP2 -TP12
VSET2 - TP7
FAULT2 - TP6
V OUT - J2 and J5 (connect to J1 when V OUT replace LED
AUX PS)
GND - J3, J6, J8, TP24-TP27
V+5V - (AUX PS for LEDs) - J1
FN9131.7
October 6, 2011
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
ISL61853EVAL1Z EVAL BOARD FOR ISL61853
ISL6227EVAL1 EVALUATION BOARD 1 ISL6227
ISL62386HIEVAL1Z EVAL BOARD FOR ISL62386HI 32TQFN
ISL6291EVAL1 EVALUATION BOARD FOR ISL6291
ISL6292EVAL2 EVALUATION BOARD 2 ISL6292
ISL6296EVAL1 EVALUATION BOARD 1 ISL6296
ISL6298EVAL1 EVALUATION BOARD 1 ISL6298
ISL6298EVAL2 EVALUATION BOARD 2 ISL6298
相关代理商/技术参数
ISL6144EVAL1Z 功能描述:EVALUATION BOARD ISL6144 ORING RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板
ISL6144IR 功能描述:IC CTRLR MOSFET HV ORING 20-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:- 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR)
ISL6144IR-T 功能描述:IC CTRLR MOSFET HV ORING 20-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:- 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR)
ISL6144IRZA 功能描述:热插拔功率分布 W/ANNEAL 20LD 5X5 QF N ORING FET CONTRLR RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
ISL6144IRZA-T 功能描述:IC CTRLR MOSFET HV ORING 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:- 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR)
ISL6144IV 功能描述:IC CTRLR MOSFET ORING HV 16TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:- 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR)
ISL6144IV-T 功能描述:IC CTRLR MOSFET HV ORING 16TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:- 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR)
ISL6144IVZA 功能描述:IC CTRLR MOSFET ORING HV 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:- 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR)